United States

The realization of energy efficient spin-current based electronics relies on the existence of low-loss magnetic insulator thin films capable of generating spin currents without an accompanying charge current. Currently, the number of such materials is extremely limited, with the only candidates being the garnets Y3Fe5O12 (YIG) [1] and Lu3Fe5O12 (LuIG) [2] along with the recently discovered spinels Ni0.65Zn0.35Al0.8Fe1.2O4 (NZAFO) [3] and MgAl0.5Fe1.5O4 (MAFO) [4,5]. Bulk phase Li0.5Fe2.5O4 (LFO) is well known to have the lowest Gilbert damping parameter (α ≈ 0.002) among the spinel ferrites, but thus far LFO thin films have not lived up to these expectations. In this talk, we demonstrate the realization of epitaxial ultra-thin (~3 nm) LFO thin films on MgAl2O4 substrates with an ultra-low damping parameter of α ≈ 0.0013 and an FMR linewidth of 1.17 mT at 20.6 GHz. Such a damping value rivals those of YIG and is comparable to the lowest damping previously reported in sub-10-nm magnetic films [2]. LFO also offers distinct advantages over YIG such as smaller external field requirements and thinner interfacial magnetic dead layers due to the low growth temperature, making it ideal for magnetic switching applications. Our results show the promise of LFO as a new candidate for spin-current based spintronics. This work was supported by the U.S. Department of Energy, Director, Office of Science, Office of Basic Energy Sciences, Division of Materials Sciences and Engineering under Contract No. DESC0008505.References: [1] B. M. Howe, S. Emori, H. Jeon, IEEE Magnetics Letters., Vol. 6, p. 1-4 (2015) [2] C. L. Jermain, H. Paik, S. V. Aradhya, Applied Physics Letters., Vol. 109, p. 192408 (2016) [3] M. T. Gray, S. Emori, B. A. Gray, Physics Review Applied., Vol. 9, p. 064039 (2018) [4] S. Emori, D. Yi, S. Crossley, Nano Letters., Vol. 18, p. 4273-4278 (2018) [5] J. J. Wisser, S. Emori. L. Riddiford, Applied Physics Letters., Vol. 115, p. 132404 (2019) 


MMM 2020

Ultra-low Magnetic Damping in Epitaxial Li0.5Fe2.5O4 Thin Films

The 65th Annual Conference on Magnetism and Magnetic Materials (MMM 2020) was held in a virtual form. The COVID-19 pandemic, with its associated uncertainty about international travel and the ability to gather in large groups, meant that the Steering Committee decided to cancel the face-to-face meeting that had been planned in Palm Beach, Florida November 2-6, 2020.

We were reluctant to give up the benefits of meeting face-to-face, and know that shifting to a virtual conference is a significant change for this community. Nevertheless, we are first and foremost concerned about the health and safety of all our Conference participants and their loved ones on returning home after travelling.

The MMM 2020 Steering Committee was working exceptionally hard, along with our sponsors, the IEEE Magnetics Society and AIP Publishing, to make this event serve the needs of our participants, who live in time zones all around the globe, in the best possible way. 

You need a ticket to explore this event.

If you have already registered for MMM 2020, and you have already created an account, then you
just need to login (above).

If you have already registered for MMM 2020, but you have not yet created an account, then you
need to click on &quot;create an account&quot; (above) and then login.

Forgot your password? Go to
https://www.underline.io/log-in

If you have not yet registered for MMM 2020 but would like to do so, go to
https://magnetism.org/register

Still need help? Contact our team!


**Please view our Welcome to MH21 video.**

<center>
<figure class="video_container">
	 <iframe src="https://screencast-o-matic.com/watch/cr1UYHV1pcz?v=6&ff=1&title=0&controls=1" width=826 height=526 frameborder="0" allowfullscreen="true"> </iframe>
</figure>
	</center>


**Walkthrough Video**

Here is a Walkthrough showing how to navigate the conference and network with others 

<center>
<figure class="video_container">
	 <iframe src="https://screencast-o-matic.com/watch/cr1vnrV1paE?v=6&ff=1&title=0&controls=1" width=826 height=526 frameborder="0" allowfullscreen="true"> </iframe>
</figure>
	</center>




	 Organized by
 
<a href="https://mrs.org.sg/">
<img src="https://s3.eu-west-1.amazonaws.com/underline.prod/uploads/markdown_image/1/image/95d5789689d5f900b90e9fe54ea3cf0d.jpg"</a>

 
	
	 In association with
 
<a href="http://www.ntu.edu.sg/">
<img src="https://s3.eu-west-1.amazonaws.com/underline.prod/uploads/markdown_image/1/image/334cd171ad2fdee033c635b368e5e160.png"</a>
	<a href="https://www.nus.edu.sg/">
<img src="https://s3.eu-west-1.amazonaws.com/underline.prod/uploads/markdown_image/1/image/32e6f82c0440f7bb24c590f9f67821bd.png"</a>
		<a href="https://www.a-star.edu.sg/">
<img src="https://s3.eu-west-1.amazonaws.com/underline.prod/uploads/markdown_image/1/image/72557865b589cfa3d2a0243ffce4a270.png"</a>
	
 


	 Supported by
 
		 <a href="https://www.visitsingapore.com/mice/en/about-us/about-secb/">
<img src="https://s3.eu-west-1.amazonaws.com/underline.prod/uploads/markdown_image/1/image/6e679842ead62be522ba6a630b82d5c9.png"</a>

To access the MH 21 Conference, [please register](https://mh21.mrs.org.sg/event/da3f9651-429f-4763-81b2-ebd7311b6bc8/websitePage:206f7605-1731-41f9-8421-56d3890f398f)

MATERIALS FOR HUMANITY (MH 21)

MH 21 is arranged around 6 themes that focus attention on pressing needs that should be addressed to enhance the well-being of communities and provide a forum for presenting breakthrough discoveries.

technical paper

This work describes a technique for 3D printing of magnetic materials at millimeter and sub-millimeter scales for microrobotic applications using stereolithography. Traditional fabrication techniques to engineer magnetic materials become very challenging at smaller scales. The need for rapid prototyping techniques using materials with tunable magnetic properties is becoming more important [1]. Unfortunately, additive manufacturing of magnets is still in its infancy [2-3]. Most reported techniques that are based on thermoplastic bonded magnets [4-5], filament extrusion [6], binder jetting [7], or laser sintering [8], have limitations for scaling down in size. A better path towards miniaturization is offered by stereolithography [9], as presented in this work. The presented technique combines magnetic particles (NdFeB, Fe or Fe3O4) with different mixing ratios to a flexible resin that is made from aliphatic urethane diacrylate, epoxy aliphatic acrylate and a photo-initiator (Irgacure 819 - Irgacure 184) [10]. 3D printed multi-material structures are presented in Fig. 1a. This work is motivated by the need to engineer complex magnetic field patterns for MEMS actuators [11-12] and micro/soft robotics (Fig. 1B) [13]. Magnetic moment was measured to evaluate dependence of saturation magnetization and coercivity with particle material and particle concentration (Fig. 2a). Torques and forces over printed samples were measured in response to external magnetic fields (Fig. 2b), demonstrating an ability to generate highly complex 3D structures for actuation at micro- to meso-scales.References: [1] G. Chatzipirpiridis et al., “3D Printing of Thermoplastic Bonded Soft and Hard Magnetic Composites: Magnetically Tuneable Architectures and Functional Devices,” Adv. Intell. Syst., vol. 1, no. 6, p. 1900069, 2019. [2] L. Li, B. Post, V. Kunc, A. M. Elliott, and M. P. Paranthaman, “Additive manufacturing of near-net-shape bonded magnets: Prospects and challenges,” Scr. Mater., vol. 135, pp. 100–104, Jul. 2017. [3] V. Popov, A. Koptyug, I. Radulov, F. Maccari, and G. Muller, “Prospects of additive manufacturing of rare-earth and non-rare-earth permanent magnets,” Procedia Manuf., vol. 21, no. March, pp. 100–108, 2018. [4] L. Pigliaru et al., “3D printing of high performance polymer-bonded PEEK-NdFeB magnetic composite materials,” Funct. Compos. Mater., vol. 1, no. 1, p. 4, Dec. 2020. [5] P. P. Wendhausen, C. H. Ahrens, A. B. Baldissera, P. D. Pavez, and J. M. Mascheroni, “Additive manufacturing of bonded NdFeB, process parameters evaluation on magnetic properties,” in 2017 IEEE International Magnetics Conference (INTERMAG), 2017, vol. 53, no. 11, pp. 1–1. [6] B. Khatri, K. Lappe, D. Noetzel, K. Pursche, and T. Hanemann, “A 3D-Printable Polymer-Metal Soft-Magnetic Functional Composite—Development and Characterization,” Materials (Basel)., vol. 11, no. 2, p. 189, Jan. 2018. [7] C. L. Cramer et al., “Binder jet additive manufacturing method to fabricate near net shape crack-free highly dense Fe-6.5 wt.% Si soft magnets,” Heliyon, vol. 5, no. 11, p. e02804, Nov. 2019. [8] C. V. Mikler et al., “Laser Additive Manufacturing of Magnetic Materials,” JOM, vol. 69, no. 3, pp. 532–543, Mar. 2017. [9] L. Lu, P. Guo, and Y. Pan, “Magnetic-Field-Assisted Projection Stereolithography for Three-Dimensional Printing of Smart Structures,” J. Manuf. Sci. Eng., vol. 139, no. 7, pp. 1–7, Jul. 2017. [10] D. K. Patel, A. H. Sakhaei, M. Layani, B. Zhang, Q. Ge, and S. Magdassi, “Highly Stretchable and UV Curable Elastomers for Digital Light Processing Based 3D Printing,” Adv. Mater., vol. 29, no. 15, p. 1606000, Apr. 2017. [11] A. P. Taylor, C. Velez Cuervo, D. P. Arnold, and L. F. Velasquez-Garcia, “Fully 3D-Printed, Monolithic, Mini Magnetic Actuators for Low-Cost, Compact Systems,” J. Microelectromechanical Syst., vol. 28, no. 3, pp. 481–493, Jun. 2019. [12] Y. Kim, G. A. Parada, S. Liu, and X. Zhao, “Ferromagnetic soft continuum robots,” Sci. Robot., vol. 4, no. 33, p. eaax7329, Aug. 2019. [13] J. J. Abbott, E. Diller, and A. J. Petruska, “Magnetic Methods in Robotics,” Annu. Rev. Control. Robot. Auton. Syst., vol. 3, no. 1, pp. 57–90, May 2020. 

Multimaterial and flexible 3D printed magnets with sub-millimeter resolution

The extension of nanomagnetism to three dimensions is proposed as an exciting route to study new physical effects, such as the emergence of new spin textures and magneto-chiral phenomena, with the prospective of being exploited in future technologies [1,2]. Whereas a significant amount of work has been so far devoted to simulating 3D nanostructures, its fabrication and characterization has proven to be very challenging, and very few of these systems have been experimentally investigated. Our group has been recently developing new fabrication and characterization methods specifically tailored for the study of 3D nanostructures, which made it possible to control the advanced motion of domain walls in 3D straight nanowires [3,4]. Here, we will present recent advances in this realm, which now enable us to create and probe nanomagnets with more complex 3D geometries. First, we will present recent work dedicated to the 3D printing of nanomagnets using Focused Electron Beam Induced Deposition (FEBID). Based on the effective FEBID continuum model [5] and proximity effect corrections, we have developed an algorithm with the capability of modelling the deposition and defining beam scanning patterns for arbitrary 3D geometries [6]. The algorithm performance has been demonstrated in different electron microscopes and precursor gases, allowing us to create 3D nanomagnets with a wide range of geometries directly from CAD files (see Fig. 1). Complementing nanofabrication, we will present a new Kerr magneto-optical setup with the ability to probe 3D magnetic nanostructures, by exploiting the dark-field MOKE (dfMOKE), a technique that we have recently developed [3]. The unprecedented flexibility of the system to characterize these newly accessible 3D geometries will be demonstrated, thanks to the combination of mobile optics and full-3D vector magnetic fields (see Fig. 2).References: [1] Fernández-Pacheco, A. et al. Nat. Commun. 8, 15756 (2017). [2] Streubel, R. et al. J. Phys. D. Appl. Phys. 49, 363001 (2016). [3] Sanz-Hernández, D. et al. ACS Nano 11, 11066–11073 (2017). [4] Sanz-Hernández, D. et al. Nanomaterials 8, 483 (2018). [5] Toth, M., Lobo, C., Friedli, V., Szkudlarek, A. & Utke, I. Beilstein J. Nanotechnol. 6, 1518–1540 (2015). [6] Skoric, L. et al. Nano Lett. 20, 184–191 (2020). 

Advanced fabrication and magnetometry of nanostructures with complex 3D geometries

A magnetic elastomer is a type of magneto-active smart material where a magnetic field induces a mechanical response. Several methods have been used to optimize performance by controlling the microstructure, such as magnetic annealing. Optimization can also be achieved by introducing anisotropy with Fused Deposition Modeling (FDM), a 3D-printing process that extrudes viscous material in 1D lines to create 2D layers which build to a 3D part. Indeed, FDM features have been shown to manipulate the magnetic anisotropy of rigid printed parts.1 However, printing flexible composite materials presents additional challenges with FDM. Here, FDM structures were printed with thermoplastic polyurethane (TPU) polymer and either 20wt% iron (Fe), 40wt% Fe, 40wt% carbonyl iron (CI), or 40wt% magnetite (Fe3O4/Mag). In order to determine the relative effect of different parameters on the magnetic properties, a series of structures were printed combining each material type (Fe-TPU, CI-TPU, Mag-TPU) with different aspect ratios (1:1 / 2:1), infill percentages (60% / 80% / 100%), and infill orientations (parallel/perpendicular to aspect ratio). A Vibrating Sample Magnetometer was used to obtain magnetic hysteresis loops for comparing magnetic susceptibility between samples. Results demonstrated that infill orientation had the largest effect on susceptibility, aspect ratio had the next greatest effect, and infill percentage had a more nuanced effect (Fig.1). This shows that FDM allows the magnetic anisotropy to manifest through mesoscale anisotropy of a part’s internal structure. These trends were found to form a continuum of tunable magnetic responses (Fig.2). Additionally, the chosen particulate transfers its unique magnetic signature to the composite material. Overall, the highly customizable and nuanced characteristics of 3D-printed magnetic elastomer structures will allow for its use in emerging magneto-mechanical applications such as magnetic actuation and soft robotics.References: 1. M. Patton, P. Ryan, T. Calascione, N. Fischer, A. Morgenstern, N. Stenger, and B. Nelson-Cheeseman, Additive Manufacturing, Vol. 27, 482-488 (2019) 


Controlling Magnetic Properties of 3D-Printed Magnetic Elastomer Structures via Fused Deposition Modeling

In geometrically frustrated magnetism, the very nature of the ground state of Tb2Ti2O7, has remained a long standing conundrum. In this pyrochlore material, no conventional spin-ice or long-range magnetic order is stabilized, even at very low temperatures [1]. Quantum fluctuations are suspected of being at the origin of such an exotic quantum phase, yet so far no complete description is available. Using neutron scattering [2] and synchrotron-based terahertz spectroscopy [3], it has been shown that spin/lattice couplings are present in form of hybrid Tb crystal-field / phonon modes that are present across a broad temperature range from 200 K down to 6 K. This so called vibronic process affects the electronic ground state that can no longer be described solely by electronic wave functions and involve quadrupolar degrees of freedom associated with the rare earth magnetic element in its local environnement. We present here new magneto-optical investigation of vibronic spin-lattice coupling effects. We apply a static magnetic field along the cubic <111> direction while probing with linearly polarized THz radiation. Through the Zeeman effect, the magnetic field enhances splitting within the low-energy Tb crystal field transitions revealing new details in our THz spectra. Complementary magneto-optical quantum calculations including quadrupolar terms show that indeed vibronic effects are required to describe our observations at 3 K. A further prediction of our theoretical model is the presence of a novel magneto-optical birefringence as a result of this vibronic process. Together, our results [4] reveal the significance of considering quadrupolar spin-lattice effects when describing the spin-liquid ground state of Tb2Ti2O7. They also highlight the potential for future magneto-optical investigations to probe complex materials where spin /lattice couplings are present and unravel new magneto-optical activity in the THz range.References: [1] J. S. Gardner, B. D. Gaulin, A. J. Berlinsky et al., Phys. Rev. B 64, 224416 (2001) [2] T. Fennell, M. Kenzelmann, B. Roessli et al., Phys. Rev. Lett. 112, 017203 (2014) [3] E. Constable, R. Ballou, J. Robert et al., Phys. Rev. B 95, 020415(R) (2017) [4] K. Amelin, Y. Alexanian, U. Nagel et al, to be published

THz Magneto-Optical Investigation of Quadrupolar Spin-Lattice Effects in Magnetically Frustrated Tb2Ti2O7

The spin nematic phase, which is a kind of multipole phases, has attracted a lot of interest in the field of the strongly correlated electron systems, as well as the quantum spin liquid phase. Using the numerical exact diagonalization, the density matrix renormalization group (DMRG) calculation, and the finite-size scaling analysis, it is found that some spin nematic and spin liquid phases are induced by external magnetic field in the anisotropic and frustrated quantum spin systems. In our previous work[1], it was found that a field-induced nematic phase appears at some critical field in the anisotropic spin ladder. The nematic phase is characterized by the power-law decay in the correlation function of the second-order spin moment. In addition at some higher critical field a quantum phase transition can occur to the conventional field-induced Tomonaga-Luttinger liquid. Several typical magnetization curves calculated by DMRG are presented. Recently the field-induced nematic phase was observed on the frustrated spin ladder system[2]. So we studied on a frustrated spin ladder system[3], using the numerical diagonalization and DMRG. As a result, it was found that several exotic quantum phases, including the spin-nematic liquid phase. We also reported several interesting phase diagrams of this model and some related systems[4,5]. In the present paper, we investigate the S=1 antiferromagnetic chain with the biqadratic interaction, as another candidate that exhibits the field-induced spin nematic liquid pahse. The numerical diagonalization study of finite-size clusters indicates that the spin nematic liquid pahse appears in this model under sufficiently strong magnetic field. The phase diagram in the plane of the magnetic field and the biquadratic interaction is presented.References: [1] T. Sakai, T. Tonegawa and K. Okamoto, Physica Status Solidi B 247, 583 (2010) . [2] N. Buttgen et al., Phys. Rev B 90, 134401 (2014) . [3] T. Hikihara, T. Tonegawa, K. Okamoto and T. Sakai, J. Phys. Soc. Jpn. 86, 054709 (2017). [4] T. Tonegawa, T. Hikihara, K. Okamoto, S. C. Furuya, and T. Sakai, J. Phys. So. Jpn. 87, 104002 (2018). [5] T. Sakai, K. Okamoto and T. Tonegawa, Phys. Rev. B 100, 054407 (2019) 

Quantum Spin Nematic Liquid in the S=1 Antiferromagnetic Chain with the Biquadratic Interaction

Spin liquids are disordered states of matter that still fluctuate at low temperature. In many cases, the ground state of spin liquids is expected to be ordered, for example because the dipolar interaction lifts the (quasi)degeneracy between low-energy spin configurations. However, this is not what is observed experimentally, and many systems dynamically freeze in a liquid phase [1] before the ordering takes place. In spin ice compounds or artificial magnets, ground state configurations are then generally out of reach for practical reasons. In this presentation, we will show how dynamical freezing can be bypassed in an artificial kagome ice. We will illustrate the efficiency of our method by demonstrating that the a priori dynamically inaccessible ordered ground state of the dipolar kagome ice is imaged reproducibly in real space, and at room temperature. The central idea of this work is to replace the spin degree of freedom by a micromagnetic knob, which can be adjusted by a proper design of the vertex geometry. Our strategy is to imprint the desired spin configuration, vertex by vertex, in a kagome array made of connected nanomagnets, with a notch at each vertex site. Each notch locally lifts the energy degeneracy between the six states of a given vertex satisfying the ice rule constraint [2], allowing to reach efficiently any desired spin microstate using a field demagnetization protocol. This concept will be demonstrated both numerically and experimentally, and we will show how we can access all predicted phases of the dipolar kagome ice [3, 4, 5].References: [1] I. A. Chioar, B. Canals, D. Lacour, Phys. Rev. B 90, 220407(R) (2014) [2] J. D. Bernal and R. H. Fowler, J. Chem. Phys. 1, 515 (1933) [3] W. R. Branford, S. Ladak, D. E. Read, Science 335, 1597-1600 (2012) [4] B. Canals, I. A. Chioar, V. D. Nguyen, Nature com. 7, 11446 (2016) [5] G.-W. Chern, P. Mellado and O. Tchernyshyov, Phys. Rev. Lett. 106, 207202 (2011). 

Bypassing Dynamical Freezing and Accessing Low-energy Microstates in Artificial Kagome Ice

The nearest neighbour antiferromagnetic Ising model on the kagome lattice is well known for its high frustration and macroscopic ground state degeneracy [1,2]. Recently, new experimental realizations of Ising-like spin systems have been developed - so-called artificial spin systems - based on mesoscopic structures of chirally coupled nanomagnets [3]. On the square lattice, such systems have proven to behave as nearest neighbour Ising antiferromagnets. Because of frustration, realizations of kagome lattice Ising antiferromagnets with these mesoscopic structures (Fig.1) are much more challenging to study. From the theoretical side as well, such models still present some difficulties [4,5]. I will describe how to tackle classical frustrated spin systems using Monte Carlo techniques [5] and tensor network methods [4,6,7] (Fig.2), focusing on the kagome lattice nearest neighbour Ising antiferromagnet in an external magnetic field, and I will compare the experimental and numerical results.References: [1] K. Kanô and S. Naya, Prog. Theor. Phys., Vol. 10, p. 158 (1953) [2] A. Sütö, Z. Phys. B, Vol. 44, p. 121 (1981) [3] Z. Luo et. al., Science, Vol. 363, p. 1435 (2019) [4] B. Vanhecke, J. Colbois, L. Vanderstraeten, et. al., arXiv:2006.14341 (2020) [5] G. Rakala and K. Damle, Phys. Rev. E Vol. 96, 023304 (2017) [6] V. Zauner-Stauber, L. Vanderstraeten, et. al. Phys. Rev. B Vol. 97, 045145 (2018) [7] L. Vanderstraeten, B. Vanhecke, and F. Verstraete, Phys. Rev. E Vol. 98, 042145 (2018) 


New Approaches to the Nearest Neighbour Ising Antiferromagnet on the Kagome Lattice

Excitation by light pulses enables the manipulation of phases of quantum condensed matter. Here, we photoexcite high-energy holon-doublon pairs as a way to alter the magnetic free energy landscape of the Kitaev-Heisenberg magnet α-RuCl3,[1,2] with the aim to dynamically stabilize a proximate spin liquid phase. The holon-doublon pair recombination through multimagnon emission [3] is tracked through the time-evolution of the magnetic linear dichroism originating from the competing zigzag spin ordered ground state. A small holon-doublon density suffices to reach a spin disordered state. The phase transition is described within a dynamic Ginzburg-Landau framework, corroborating the quasistationary nature of the transient spin disordered phase. Our work provides insight into the coupling between the electronic and magnetic degrees of freedom in α-RuCl3 and suggests a new route to reach a proximate spin liquid phase in Kitaev-Heisenberg magnets.[4]References: [1] A. Banerjee et al., Proximate Kitaev quantum spin liquid behaviour in a honeycomb magnet, Nat. Mater. 15, 733-740 (2016). [2] H. Takagi et al.,Concept and realization of Kitaev quantum spin liquids, Nat. Rev. Phys. 1, 264-280 (2019). [3] Z. Lenarcic et al., Ultrafast charge recombination in a photoexcited Mott-Hubbard insulator, Phys. Rev. Lett. 111, 016401 (2013). [4] R.B. Versteeg et al. Nonequilibrium quasistationary spin disordered state in the Kitaev-Heisenberg magnet α-RuCl3, arXiv:2005.14189 [cond-mat.str-el] (2020) 


Nonequilibrium quasistationary spin disordered state in the Kitaev-Heisenberg magnet α-RuCl3

One dimensional spin S = 1/2 chain systems provide a perfect platform to explore many of the quantum phenomena and the related excitations. We report here the discovery of a stimulating magnetic ground state in a tetragonal compound Ti4MnBi2 that contains perfectly linear chains of Mn-ions with dMn-Mn = 2.49 Å running along the crystallographic c-axis and which are separated from each other by a large interchain distance dchain ≈7.4 Å. Our electrical transport measurements and electronic structure calculations establish that compound is metallic. Curie-Weiss fit to the susceptibility data suggests that Mn moments are in low-spin S = 1/2 configuration. The results show that despite the presence of a sizable antiferromagnetic (AFM) interaction [Jc = 18(6) K], the full-moment long range magnetic ordering is not achieved down to 50 mK. Neutron diffraction measurement performed on an assembly of aligned single crystals detect a weak AFM order within the Mn chains, with a further evidence of the reduced-moment ordering coming from heat capacity data. Apparently, strong quantum fluctuations overcome the magnetic order and the material enters into a state at low temperatures which can be best described as a ``quantum admixture" of a quantum spin liquid and a long-range magnetically ordered states, resulting into a highly reduced value of the ordered moment μ << 1 μB.References: A. Pandey, P. Miao, M. Klemm, H. He, H. Wang, X. Qian, J. W. Lynn, and M. C. Aronson, Phys. Rev. B in press (2020).

Incipient antiferromagnetic order in metallic Ti4MnBi2 containing linear Mn chains of spin S = 1/2

Confirming the origin of Gilbert damping by experiment has remained a challenge for many decades. This is the case even for some of the simplest and most technologically relevant ferromagnetic metals, such as pure Fe. Here, we experimentally identify intrinsic Gilbert damping that increases with decreasing electronic scattering in thin films of BCC Fe [1]. We directly compare the temperature dependence of Gilbert damping and electronic transport in pristine epitaxial films (Figure 1). Our observation of “conductivity-like” damping, which cannot be accounted for by classical eddy current loss, is in excellent quantitative agreement with theoretical predictions of Gilbert damping due to intraband scattering (often understood in terms of the “breathing Fermi surface” model) [2,3], as shown in Figure 2. While this fundamental damping mechanism was originally proposed more than 40 years ago [4], our study is the first to confirm it unambiguously for thin films of a pure ferromagnetic metal. Our results also reveal – somewhat counterintuitively – that disorder can reduce intrinsic damping in ferromagnetic metals particularly at low temperatures. This suggest that optimally disordered films may exhibit enhanced spin coherence required for cryogenic and quantum information devices.References: [1] B. Khodadadi, A. Rai, A. Sapkota, et al. Phys. Rev. Lett., Vol. 124, 157201 (2020). [2] K. Gilmore, Y. U. Idzerda, and M.D. Stiles, Phys. Rev. Lett., Vol. 99, 27204 (2007). [3] S. Mankovsky, D. Kodderitzsch, G. Woltersdorf, and H. Ebert, Phys. Rev. B, Vol. 87, 14430 (2013). [3] V. Kamberský and Czechoslov. J. Phys., Vol. 26, 1366 (1976).

Ultra-low Magnetic Damping in Epitaxial Li0.5Fe2.5O4 Thin Films

Downloads

Next from MMM 2020

Multimaterial and flexible 3D printed magnets with sub-millimeter resolution

Similar lecture

Enhancing magnetism in Fe-Al alloys by increasing chemical disorder

Stay up to date with the latest Underline news!

PRESENTATIONS

CONFERENCES

COMPANY

RESOURCES