United States

CVD graphene has brought interest from the biosensors community. Previous work in our group demonstrated a unique fabrication protocol for graphene solution gated field effect transistor (SGFET). This study presents the electrochemical characterization and first biological detection campaign (using aptmamers as probe for hormone detection) of our SGFET sensors.

EIPBN 2021

Electrochemical characterization of graphene gated field effect transistors: route for smart biological sensors

aptamers

biodetection

sgfet

graphene

It is our great pleasure to invite you to attend the 26th International Workshop on Rare Earth and Future Permanent Magnets and Their Applications (REPM2021) which will be held virtually on June 7-10, 2021. Please note, this is an updated schedule due to COVID-19 travel restrictions which forced us to postpone the conference from summer of 2020. The REPM workshop takes place every two years and is the premier conference on permanent magnets covering a wide range of topics including:

* Rare earth magnets
* Rare earth-free magnets
* Raw materials, mining and recycling
* Advanced synthesis, processing and characterization techniques
* Theoretical modeling of coercivity
* Fundamental properties of advanced magnetic materials
* Thin film magnets
* Applications of permanent magnets

***Workshop***
The workshop will be chaired by Professor George C. Hadjipanayis, University of Delaware, Newark, DE and Dr. Jinfang Liu, President & COO of Electron Energy Corporation, Landisville, PA.
The objectives of the workshop are to bring together engineers and scientists who work on permanent magnets and their applications to present their latest results and exchange ideas on a wide range of relevant topics including resources, raw materials, recycling, processing, fundamental and hard magnetic properties and applications of rare earth and future magnets.

To regsiter for this event, please follow the link below.

REPM 2021: The 26th International Workshop on Rare-Earth and Future Permanent Magnets and their Applications

technical paper

The International Conference on Electron, Ion and Photon Beam Technology and Nanofabrication (EIPBN), affectionately known as "3-Beams," is the premier gathering of scientists and engineers who are dedicated to electron, ion and photon lithography, imaging, and analysis; atomically precise fabrication; nanofabrication process technologies and related emerging technologies; and their applications in a broad spectrum of fields. In its 64th meeting, researchers from academia, government laboratories, and industry from around the world meet to present and discuss recent and future trends in these technologies.
 
 
 
[![](https://assets.underline.io/uploads/markdown_image/1/image/4bdf4450aa93073cd684b096b403df2e.png)](https://drive.google.com/file/d/1CPaA3-Yf7_maBxJMUJaUORLF3HGO9CIe/view?usp=sharing) [![](https://assets.underline.io/uploads/markdown_image/1/image/cea8a407085dee5422a2c16738ce27ca.png)](https://eipbn.org/abstracts/2021/)

To register for this event, please follow the link below.

In this paper we report a series of breakthroughs that led to replication of gratings with a slant angle up to 60° and an aspect ratio of 10:1 in a material with refractive index of 1.90 (RI). A study of the replication process and materials optimization will be presented.

Nanoimprint process to mass manufacture highly-angled high-RI gratings for augmented reality combiners

Sequential vapor infiltration (SVI) with trimethylaluminum into UV-cured films visualized the presence of internal layered structures with different Al distributions dependent on chemical structure of monomers. X-ray reflectivity measurements revealed that the mixing of monomers was a positive way to homogenize the Al distributions in UV-cured films.

Internal Layered Structures of UV-Cured Thin Films after Sequential Vapor Infiltration Analyzed by X-ray Reflectivity Measurements

Until now, no in-situ, non-destructive and accurate technology has been invented, which introduces huge difficulties into the superhydrophobic surfaces research and applications. We developed an optical technology to characterize the state of superhydrophobic surface.

Optical Metrology of Characterizing Superhydrophobic States on Patterned Substrates

In direct writing laser lithography, hybrid structures such as gratings on top of resist structures can be generated by combining thermal NIL with DWL lithography. At 120 °C, it is still possible to pattern the resist into at least 4 µm depth without degrading the photosensitive component.

Hybrid structures achieved by direct writing laser lithography - tuning the contrast and surface topography of grayscale photoresist with nanoimprint lithography

Colors produced from nanostructures of different geometries and materials in 2D and 3D made mostly using 3D printing with two-photon polymerization.

Nanostructured Colors from Colorless Materials

We investigated the combination of maskless UV lithography and 2PP (two-photon polymerization) on a standard photo-resist: SU-8. 2PP technology is known to be slow. The advantage of mixing the technologies becomes obvious when some elements of a design can be exposed faster using maskless UV lithography.

Hybrid 2D & 3D Lithography

In this work, we discuss the fabrication process for two types of low-index metalenses composed of air-spaced elements.  First, we discuss the fabrication of our recently demonstrated two element hybrid achromatic metalens (HAML)  that employs nanopillars. Second, we discuss a novel air-spaced, varifocal, metalens that employs nanoholes.

Achromatic and Varifocal Metalens Doublet Fabrication by Two-photon Lithography

We present 3D printed Hybrid metasurfaces that employ variable height (3D) phase plates, pillars, and holes that provide additional degrees of freedom beyond purely planar designs. These structures were 3D printed with two-photon lithography technique.

Hybrid Metasurface Fabrication Using Two-photon Lithography

Molybdenum disulfide, as  a transition metal dichalcogenide, has attracted huge attention for its good optical properties. However, to produce corresponding arrays of nano/microscale devices, resist-based lithography and etching generate permanent contaminations and damages. Here, we report a  method capable of generating arbitrary MoS2 patterns without additional lithography or etching processes.

Multiplexing Rubbing-Induced Site-Selective (RISS) Method for Manufacturing MoS2 Device Arrays

In this work, we study the photo-response properties (e.g., photoresponsivity and noise equivalent power (NEP)) of in-plane MoS2 photodetectors as the function of their geometric dimensions (e.g., thickness, length, and width of photoactive layers) and fabrication conditions (e.g., doping, etching, and substrate choice).

Premium content

Downloads

Next from EIPBN 2021

Nanoimprint process to mass manufacture highly-angled high-RI gratings for augmented reality combiners

Similar lecture

Nd-Fe-B sintered magnets obtained by mechanical ball milling with rGO addition

Stay up to date with the latest Underline news!

PRESENTATIONS

CONFERENCES

COMPANY

RESOURCES