United States

Ocean related activities are often supported by offshore equipment with particular power demands. These are usually deployed at remote locations and have limited space, thus small energy harvesting technologies, such as photovoltaic panels or wind turbines, are used to power their instruments. However, the inherent energy sources are intermittent and have lower density and predictability than an alternative source: wave energy.1 The triboelectric nanogenerator (TENG) is a promising and efficient energy harvesting technology capable of addressing these problems as it can efficiently convert regular/irregular external mechanical energy into electrical power based on the triboelectrification and electrostatic induction effects.2-4 In this work, three TENGs based on rolling-spheres were developed and their performance compared in both a “dry” bench testing system under rotating motions, and in a large-scale wave basin under realistic sea-states installed within a scaled navigation buoy. The experiments showed that the electrical outputs of these TENGs tend to rise with increasing pitch amplitudes and decreasing period due to the increase of the spheres’ velocity. The capability of these TENGs to harvest energy from ocean waves when incorporated into a navigational buoy was demonstrated under realistic sea states. The voltage generated by the TENGs achieves maximum values for periods close to the natural period of the scaled buoy (~ 0.92 s). The wave basin tests clearly demonstrated a significant dependency of the electrical outputs on the pitch degree of freedom and the need to consider the full dynamics of the buoy, and not only that of TENGs, when subjected to the excitations of waves.

AIP Publishing Horizons - Energy Storage and Conversion

Performance of triboelectric nanogenerators based on rolling spheres motion under realistic water waves conditions

triboelectric nanogenerators

wave energy

ocean waves

marine buoys

#### Welcome to the 67th Annual Conference on Magnetism and Magnetic Materials, MMM 2022!

The Conference was held from October 31 to November 4 and offers both in-person and on-demand content.

MMM 2022 is sponsored jointly by AIP Publishing and the IEEE Magnetics Society. Members of the international scientific and engineering communities interested in recent developments in fundamental and applied magnetism are invited to attend and contribute to the technical sessions. The technical program will include invited and contributed papers in oral and poster sessions, invited symposia, a tutorial, and several special sessions. This Conference provides an outstanding opportunity for worldwide participants to meet their colleagues and collaborators and discuss developments in all areas of magnetism research.

<iframe width="560" height="315" src="https://s3.amazonaws.com/pf-user-files-01/u-59356/uploads/2022-11-02/un13zp7/MMM%20Welcome%20Video%20v5.mp4" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> <br>



For tickets to the event, please register at the following link: https://magnetism.org/registration

Please register for the MMM 2022 conference to join the event.

MMM 2022

This Conference provides an outstanding opportunity for worldwide participants to meet their colleagues and collaborators and discuss developments in all areas of magnetism research.

poster

Energy conversion and storage is a critical part of modern society. Applications continue to develop at a fast pace, from the development of new generation battery materials, to environmental sensors, catalytic materials for sustainable energy and solar cells and photodetectors. This conference will cover the latest advances in energy related fields and debate the needs and priorities currently existing or emerging in this field over the next few decades.

Conference Topics:

* Batteries and supercapacitors
* Catalytic materials and water splitting
* Light emitting materials and devices
* Solar cells and photodetectors
* Thermoelectric materials
* Sensing and environmental monitoring systems


If you have any questions, please visit the [Help Desk](https://underline.io/events/155/help-desk). 

To access the AIPP Energy Storage and Conversion conference, [please remember to register.  ](https://services.aip.org/AIPPHorizons/?confID=3351205)

Energy conversion and storage is a critical part of modern society. Applications continue to develop at a fast pace, from the development of new generation battery materials, to environmental sensors, catalytic materials for sustainable energy and solar cells and photodetectors. This conference will cover the latest advances in energy related fields and debate the needs and priorities currently existing or emerging in this field over the next few decades.

A study on the effects of porosity on the capacitance of p-doped Si electrodes was carried out in the presented work. For that two different parameters, namely the porosification time and the current density applied in the anodization process have been varied and as a result 12 types of porous Si electrodes, corresponding to 6 different current densities and 2 different time durations, were obtained and evaluated in a plane parallel capacitor configuration through EIS, CV and C&D measurements. In addition to porosification, the electrodes have also been modified through electrodeposition of a conductive polymer and thermal treatment towards obtaining activated carbon at the surface.

In-depth analysis of porous Si electrodes for supercapacitors

The successful isolation of graphene (in 2004) and phosphorene (atomic layer thick black phosphorus) in 2014 and MXene (year 2011) has currently aroused the interest of 2D material researchers. In this review, first, the fundamentals of graphene and phosphorene and MXene, are briefly introduced, along with their structures, properties, and synthesis methods. Second, the readers are presented with an overview of their energy applications. Particularly in electrochemical energy storage, the large interlayer spacing (0.53 nm) in phosphorene allows the intercalation/deintercalation of larger ions as compared to its graphene counterpart (0.33 nm). Therefore, phosphorene may possess greater potential for high electrochemical performance for sodium ion batteries while graphene hold the promise for lithium ion batteries. Next, each application for energy generation, conversion, and storage is described in detail with milestones as well as the challenges. These emerging applications include supercapacitors, photovoltaic devices, water splitting, photocatalytic hydrogenation, oxygen evolution, and thermoelectric generators. Finally the fast-growing dynamic field of 2D research is summarized and perspectives on future possibilities are presented calling on the efforts of chemists, physicists, and material scientists.

Energy conversion and storage applications of graphene, phosphorene and Mxene

Photovoltaic (PV) devices such as GaAs, GaInP, organic and perovskite solar cells are highly desirable for harvesting ambient light energy and generating small amounts of power sufficient to run rechargeable batteries and sensors1. However, accurate test methods for measuring the electrical performance parameters of these devices under artificial light sources such as light emitting diodes, incandescent, or fluorescent lighting are lacking. Furthermore, fundamental energy loss mechanisms under these non-conventional lighting sources are not well understood.2,3 In this work, we describe the methodology and results of an accurate, reference-solar-cell-based method for measuring the current vs voltage (I-V) characteristics of solar cells under a variety of unique ambient light sources at an illuminance of 1000 lx or less. We describe some unexpected findings with implications for accurate characterization, such as sub-bandgap spectral effects in solar cells grown on heterosubstrates, and we unambiguously show how power conversion efficiency can be accurately determined. Additionally, we use absolute electroluminescence measurements to compute nonradiative recombination losses in these cells and, with additional energy loss calculations, display a clear picture of the balance of energy within each cell under unique ambient lighting conditions.

Measuring and understanding PV performance under ambient lighting

Small battery-powered electronic devices such as the Internet-of-Things (IoT) wireless sensors and actuators have found widespread use in many building environments in recent years. However, these devices rely on battery power and batteries need charging or replacement. Current research efforts have focused on finding ways for these sensors to self-harvest energy from the environment in which they are installed1. Indoor photovoltaics (IPV) are an intuitive choice for harvesting the wasted indoor ambient light, even under low light conditions, and using it to charge the battery and powering of these devices2. In this work, we investigate battery charging properties of small rechargeable batteries from low charge to full charge, by assembling and using PV mini-modules of three different technologies, including monocrystalline silicon (c-Si), gallium-indium-phosphide (GaInP) and gallium-arsenide (GaAs) under broadband LED lighting at an illuminance of 1000 lx. Battery charging times are shortest for the more efficient GaInP and GaAs mini-modules whose spectral responsivity are a better match to the LED test source, which contains mostly visible photons, and longest for the less efficient Si cells. As a demonstration, a wireless temperature sensor mote was attached to the charging circuit and operated to determine its power consumption in relation to the available charging power. The mote’s maximum power draw was less than the charging power from the least efficient c-Si mini-module. Our findings affirm the feasibility of utilizing PV under typical indoor lighting conditions to power IoT devices.

Indoor photovoltaics for battery-powered sensors

In the recent past, organometal halide perovskites have gained huge attention for application in various optoelectronic devices such as solar cells, light-emitting diodes (LEDs), photo-detectors, Lasers, etc.1,2 Such a wide range of applications are attributed to the extraordinary properties of these materials such as large range energy bandgap tunability from 2.43 eV to 1.50 eV, large absorption coefficients (~21.026 mm-1), large charge carrier lifetimes (~260 μs), mobilities (μe=73 cm2/V-sec, μh=43 cm2/V-sec), and diffusion lengths (~7.7 µm).3–6 However, the instability of bulk perovskite materials in ambient air conditions limits their usage at the device level. Contrary to bulk counterparts, the low-dimensional, as well as quasi dimensional perovskites, show improved stability which is promising for the development of these materials for optoelectronic devices. We present, the Ruddlesden-Popper phase 2D perovskites of type (CH)2(MA)n-1PbnI3n+1, [CH=2-cyclohexylethylamine; MA=methylamine] where, n is an integer and represents the number of inorganic layers of PbI6 octahedron in the perovskite crystal structure (Figure 1a). The spin-coating of these materials results into self-assembled highly crystalline films. The energy bandgap (Eg) of these films decreased with an increase in n-value and upon illumination with λex~470 nm LED strong and tunable photoluminescence is observed (Figure 1b). Photocurrent density (λex~470 nm) for the photo-detectors is found to increase with increase in n-value from 16.67 nA/cm2 (n=1) to 67.78 nA/cm2 (n=4) at 0V bias as well as with increase in bias.

Investigation of 2D Ruddlesden-Popper Perovskites Optoelectronic Devices

Thermally chargeable supercapacitor is a new module in the field of thermoelectric conversion, which can simultaneously produce and store electric energy from heat source. In this paper, we use biomass derived carbon materials as the electrode of TCS, and mainly explore the effect of different electrolyte concentrations on the thermal charging performance of TCS. The application of biomass electrode with ultra-high specific surface area provides a guarantee for ion intercalation and adsorption, so that the system can produce a larger energy density at a lower temperature difference. The open circuit voltage of TCS system with different electrolyte concentration under the same temperature difference is experimentally measured. The results show that the electrolyte concentration has a significant effect on the thermal charging behavior of TCS. By adjusting the electrolyte concentration, the system can get the best temperature coefficient under the same temperature difference. This research can provide a new idea for the design of TCS.

Effect of electrolyte concentrations on electrochemical performance of thermally chargeable supercapacitor composed of biomass-derived electrodes

Bismuth-based metal oxides are an intriguing class of photoelectrode materials that can potentially enable large-scale solar hydrogen production via photoelectrochemical (PEC) water splitting. Due to their so-called defect tolerance features including other favorable photophysical and photoelectrochemical properties, Bismuth vanadate (BiVO4) and kusachiite (copper bismuth oxide) (CuBi2O4) are perhaps the most promising photoanode and photocathode materials for attaining high solar-to-hydrogen efficiency (STH). BiVO4 (BVO) has three different polymorphs; namely pucherite, dreyerite, and clinobisvanite. Here we attempt to synthesize phase pure BiVO4 with monoclinic scheelite (ms) crystal structure using a facile solid-state reaction technique aided with a two-step sintering process at ~ 400 – 500 0C for BVO and at ~750 0C for 4 h in the air for CBO. Both BiVO4 and CuBi2O4 powders have been synthesized utilizing a facile solid-state reaction technique for subsequent sol-gel derived fabrication of photoelectrodes atop the transparent conducting substrates. The structural, optical, and Raman studies suggest that phase pure ms BiVO4 and tetragonal CuBi2O4 could be grown from inorganic oxide powder as raw materials. We estimate the crystallographic lattice parameters and crystal domain size from X-Ray diffraction measurements. The crystallographic and vibrational structures are further analyzed with room temperature Raman spectroscopy. We observe clear evidence of ms crystal structure in our synthesized sample based on X-ray and Raman peak analyses. The optical bandgap measured in the range of ~2.38 – 2.58 eV for BiVO4 and ~1.70 – 1.85 eV for CuBi2O4 from the UV-VIS-NIR Diffuse reflection spectroscopy further corroborates the ms BiVO4 structure. The ms BiVO4 photoanode and CuBi2O4 photocathode with variable structural and optical properties could be a promising candidate for self-sustained PEC generation of solar fuels.

Facile Synthesis and Characterization of BiVO4 and CuBi2O4 for self-sustained photoelectrochemical water splitting devices

Organic solar cells (OSCs) based on nonfullerene acceptors (NFAs) have achieved rapid developments benefiting from the near-zero donor/acceptor (D/A) energy offset. However, a specific mechanism underlying the high-efficient charge generation remains an open question. Up to now, most of studies only focused on intra-molecular charge transfer (Intra-CT) character and inter-molecular aggregation structure of NFAs, but ignored their inter-molecular charge transfer (Inter-CT) character. In this study, by emphasizing the intra-molecular A-D-A electronic structure and inter-molecular aggregation mode of typical NFA molecules, we propose a universal quantum model incorporating both Intra- and Inter-CT characters. We confirm that the Inter-CT character is intrinsically presented in NFA molecular aggregates. Importantly, owing to the Intra- and Inter-CT synergistic effect, the excited state binding energy in NFA molecular aggregates can be significantly reduced (lowered to ~0.05 eV). These results clearly demonstrate that the excited state in NFA molecular aggregates is a CT state with both Intra- and Inter-CT characters, by which the charge generation dependence upon the D/A energy offset can be eliminated through rational designs of NFA molecules. 


Synergistic Effect Incorporating Intra- and Inter-Molecular Charge Transfer in Nonfullerene Acceptor Molecules for High-Efficient Organic Solar Cells

As a promising strategy, strain engineering has been applied to different low-dimensional or flexible semiconductor materials, aiming to modulate their photoelectric properties. An interesting experimental result is the directional migration of the photogenerated excitons induced by a local nonuniform strain in these systems, such as “exciton funneling”. Herein, to clarify the related microcosmic quantum dynamics and the impacting factors, we theoretically demonstrate the migration dynamics of an exciton/biexciton induced by a funnel-like nonuniform compression strain over organic polymers, where a quantum model combined with the nonadiabatic dynamical method is employed. Firstly, the migration dynamics of an exciton and a biexciton are separately demonstrated right after a funnel-like nonuniform compression strain created. It is found that both of them will migrate towards the strain center with the speeds two orders of magnitude higher than those determined by the traditional Förster or Dexter mechanism. Furthermore, we clarify the mechanism for the directional and ultrafast migrations of the exciton/biexciton, and compare the difference between their migration dynamics. In addition, some typical factors impacting the exciton migration dynamics are considered, such as the non-uniform degree of the strain, the initial interchain distance of organic polymers, and the proportion of the exciton initially lying in the strain region.

Migration dynamics of excitons/biexcitons induced by a funnel-like nonuniform compression strain over organic polymers

By employing a femtosecond electric pump pulse, we theoretically investigate the re-excitation dynamics of a “cold” charge transfer (CCT) state at organic donor/acceptor (D/A) interfaces. It is demonstrated that a relaxed CCT state can be pushed to different “hot” CT (HCT) states via experiencing electron (HCT1 state) and/or hole (HCT2 state) higher-energy transitions, where the transition modes and probabilities are primarily determined by the pulse energy. Without the assistance of a charge driving field, both the two HCT states relax to the initial CCT state through different internal conversion processes, which dynamics are clearly clarified in this work. However, after a driving field applied, we find that both of the two HCT states can be dissociated into free charges before their relaxations. Especially, HCT2 state is much easier dissociated than HCT1 state, as well as CCT state, due to the more delocalized hole charge distribution along donor. In addition, by enhancing the pulse intensity, we can further improve the hole delocalization along donor, so that the pulsed HCT2 state is more favorable to be dissociated. This work underlines the importance of charge delocalization for the interfacial charge dynamics, including both the internal conversion and charge separation, mediated by different intermediate HCT states in organic solar cells.

Premium content

Next from AIP Publishing Horizons - Energy Storage and Conversion

In-depth analysis of porous Si electrodes for supercapacitors

Similar lecture

Extremely Low Frequency Multi Directional Electromagnetic Wave Energy Harvester Based on Special Double Pendulum Structure

Stay up to date with the latest Underline news!

PRESENTATIONS

CONFERENCES

COMPANY

RESOURCES